Robotics DIY kits on this page are loose parts for building circuits as groundwork for robotics: a breadboard starter kit, transistors and diodes, a light sensor and LEDs, small motors, a battery holder and a multimeter for fault-finding. Robotics clubs, tinkering labs and college electronics classes use them when students design, wire and repair their own builds. The Fundamentals of Electronics kit and the Mini Motor Unit are made by ScienceLab in Ambala, and the loose components are supplied by ScienceLab, Ambala.
| Group | What it covers | Example products |
|---|---|---|
| Starting on a breadboard | A starter kit built around a solderless breadboard, with transistors, a diode, LEDs, a buzzer, capacitors, resistors, a photo resistor and a teacher's guide, plus packs of male-to-male jumpers. | Fundamentals of Electronics, Jumper Wires (male to male) |
| Semiconductors | NPN and PNP transistors for switching a motor or LED from a small control signal, and diodes that let current pass one way only. | NPN Transistor, PNP Transistor, Semiconductor Diode |
| Sensing and indicating | A cadmium sulphide light sensor whose resistance falls as more light reaches it, and standard LEDs in several colours. | Light Dependent Resistor, LED Bright Red, LED Blue |
| Motors and power | A miniature DC motor with solder tags, a small DC motor on a base for bench tests, and a holder for a single C cell. | Electric Motor, Mini Motor Unit, Battery Holder, C |
| Testing and fault-finding | A portable digital multimeter for voltage, current and resistance, with diode test and an on/off buzzer for tracing breaks. | Standard Digital Multimeter |
Begin with the Fundamentals of Electronics kit, whose activities run from lighting an LED through a resistor to using a transistor as a switch, with a Teacher's Guide for planning. Next, add the Light Dependent Resistor to make a light-activated circuit, then let an NPN Transistor switch the Electric Motor. The Mini Motor Unit sits on a base, so it suits bench tests before a motor is fixed into a model.
Sort loose parts into labelled trays by type and value, and count them out to each team at the start of a session. Keep jumper wires short and use one colour for the positive rail and another for the negative, so a faulty build can be traced quickly. Order extra LEDs, transistors and jumpers, since these are the parts most often lost or damaged.
Work from cells only, and disconnect the battery before any wiring is changed. Insert LEDs, diodes and transistors the right way round, as each works in one orientation only. The Electric Motor has solder tags, so permanent joints are soldered by the teacher or by trained older students with the iron in its stand.
With the kit, then loose parts. The Fundamentals of Electronics kit holds a breadboard, both transistor types, a diode, LEDs, a buzzer, capacitors, resistors, a photo resistor, switches and wires, so a team can learn the basic circuits first. Projects then add loose parts: jumper wires come in packs of 40, and LEDs, transistors and diodes are listed separately.
The type or value the circuit diagram calls for. The NPN, PNP and diode pages each say different values are available, so name the part before ordering. Ask for the pin layout as well, because the order of emitter, base and collector differs between transistor types, and a transistor wired with its pins swapped will not switch.
Most often a part sits the wrong way round or a connection is loose. Check that each LED and diode faces the right way, that every lead is in the intended row, and that jumper wires are pushed fully home. Then use the Standard Digital Multimeter to follow the voltage from the battery to each part in turn.
A motor draws a large current as it starts, and that can pull the battery voltage down for a moment. LEDs dim and a transistor circuit may stop switching cleanly. Give the motor its own cell in a Battery Holder, C, switch it through a transistor, and use fresh cells. The Electric Motor runs on 1.5 to 4.5 V DC.
No. It can switch or amplify. As a switch, a small base current turns a much larger collector current fully on or fully off, which is how a light sensor can control a motor. As an amplifier, it is held part-way on, so the collector current follows small changes in the base current.
No. The battery supplies it, and the transistor only controls how much current flows. An NPN transistor switches on when its base is made positive with respect to the emitter, while a PNP transistor switches on when its base is taken negative with respect to the emitter. Their symbols show this by the direction of the emitter arrow.
Breadboard parts, transistors and small motors for club builds come under the ScienceLab name from Jain Scientific Equipments Pvt Ltd in Ambala. A club can put NPN Transistor values and packs of Jumper Wires (male to male) on the same parts list as the breadboard kit and motors. Schools and dealers in 110 countries already order from ScienceLab, so a DIY parts list can travel with a wider science order. See the ScienceLab company profile.
To request a quotation or a catalogue for this range, send the product names, codes and quantities through our contact page or add the items to your enquiry cart.
Last updated: 16 November 2026