Robotics STEM kits on this page are ready-made circuit modules on bases that lay the groundwork for robotics, from switch and light-sensor inputs to LED, buzzer and motor outputs, a reed relay, and solar and timing units. Schools and junior colleges use them in teacher-led lessons on how a machine senses, decides and acts. The buzzer and reed relay modules are made by ScienceLab in Ambala, and the other items are supplied by ScienceLab, Ambala.
| Group | What it covers | Example products |
|---|---|---|
| Inputs | A push button that opens and closes a circuit, and a light dependent resistor board whose resistance rises when it is shaded. | Simple Circuit Module Push Switch, Simple Circuit Module Light Dependent Resistor Board |
| Outputs | LED boards with their own series resistor, a low-current buzzer that sounds on a very small current, and a low-voltage d.c. motor on a base. | Simple Circuit Module LED Board Red, Simple Circuit Module Buzzer, Simple Circuit Module Motor |
| Switching and control | A reed relay that lets the current in one circuit switch a second, separate circuit, as a controller does in a robot. | Simple Circuit Module Reed Relay |
| Energy for movement | A selenium solar cell on a base that drives a small mounted motor directly, turning light into motion. | Mounted Solar Cell, Mounted Motor for Solar Cell |
| Measuring motion | A ticker tape timer that dots the path of a moving trolley on paper tape, and a large countdown timer for timed runs. | Ticker Tape Timer, Digital Timer |
Build each lesson as a chain from input to output. Start with the push switch lighting an LED board, then swap the switch for the light dependent resistor board so the LED answers to light instead of a finger. Add the buzzer module as an alarm, and bring in the reed relay once students are ready to see one circuit switch another.
Give each group the same set, with one more kept for the teacher's demonstration. Label every module and lead with its set number, and count the set back into its box at the end of the lesson. Students record each circuit as a block diagram of input, control and output, which is the same plan a robot's designer starts from.
Power every module from cells or a low-voltage DC supply; no student circuit is ever connected to a wall socket. Push plugs in straight rather than forcing them at an angle, and take cells out of their holders before the sets are stored. The ticker tape timer is set up and switched on by the teacher, and students stand clear of the striker while it runs.
Cells or a low-voltage DC supply, with the Mounted Solar Cell as a light-powered option for its motor. The LED boards carry their own series resistor, and the buzzer sounds on a very small current, so a weak cell still gives a result. Before the lesson, test each set's cells, check leads for breaks and make sure every module is in the box.
Spare cells, a few extra connecting leads and one or two of each output module cover most breakdowns. The ticker tape timer also needs paper tape and replacement Ticker Tape Carbon Disc packs. Keep a simple list of usable and damaged stock, and check each set for missing modules at the end of every term.
Usually one set for every group of two to four students, plus one for the teacher. Larger groups leave some students watching rather than wiring. Each set needs at least one input, one output and enough leads to join them, and a relay or solar cell can be shared between two groups when those lessons come up.
Both are inputs, but they work differently. A switch makes or breaks the circuit when something presses it, as the push switch module does. A sensor responds to a condition around it: the light dependent resistor board changes its resistance with the light falling on it, so the circuit reacts to brightness without being touched.
The motor module is the actuator that makes something move, the LED boards give light and the buzzer gives sound. Each turns electrical energy into a result the user can see or hear. The reed relay sits between input and output, letting a small control current switch a second circuit, much as a robot's controller switches its motors.
Yes, and most real control systems do. Put the push switch and the light dependent resistor board in series with an LED board, and the LED glows brightly only when the button is pressed and the board is in light. Students can then predict and test what each combination does before moving on to logic gates.
Jain Scientific Equipments Pvt Ltd supplies the switch, sensor, output and relay modules under the ScienceLab name from Ambala. A class order can add Banana/Alligator Cords for joining modules to meters and a box of Ticker Tape Carbon Disc spares for the timer. Whole-class sets of these modules go out to schools and dealers in 110 countries. See the ScienceLab company profile.
To request a quotation or a catalogue for this range, send the product names, codes and quantities through our contact page or add the items to your enquiry cart.
Last updated: 16 November 2026