This economy ripple tank lets a class watch water waves reflect, refract, diffract and interfere on a large transparent viewing surface. A tough moulded frame holds a 405 x 405 mm tank whose sloping sides minimise noise in the pattern. A 12V halogen lamp on an adjustable arm lights the waves, and a motor-driven ripple bar sends straight wavefronts across the water.
| Parameter | Detail |
|---|---|
| Tank, internal size | 405 x 405 mm |
| Tank, external size | 420 x 420 mm |
| Tank sides | Sloping, to minimise noise |
| Frame | Tough moulded frame with a large transparent viewing surface |
| Light source | 12V halogen lamp on a lamp unit with adjustable arm |
| Wave generator | Ripple motor with eccentric cam mounted on the ripple bar |
| Wave accessories | Curved reflector, 2 barriers, roller bar, point dippers, concave perspex plate, rectangular perspex plate, hand stroboscope |
| Mounting parts | 4 push-fit legs, 3 support pillars, 2 motor support springs, 2 ripple bar hanging hooks |
| Power supply | Not included |
| Product code | SLE/PHY/121 |
| Minimum order | 10 units |
| Dispatch | Usually within 7 to 10 working days |
| Manufacturer | ScienceLab (Jain Scientific Equipments Pvt Ltd), Ambala, India |
Wavelength, frequency and wave speed. Run the motor at a steady rate and view the pattern through the hand stroboscope until the bands stand still. Measure across several bright bands and divide to get one wavelength. Time a counted number of waves with a digital stopwatch, or read the flash rate from a xenon stroboscope, then multiply frequency by wavelength to get the speed.
Reflection at plane and curved surfaces. Lay one barrier across the tank at an angle and roll the roller bar once to send a single straight pulse. Trace the incident and reflected wavefronts and compare the two angles. Swap in the curved reflector and mark the point where the reflected waves meet.
Refraction over a shallow region. Place the rectangular perspex plate under the water so that part of the tank becomes shallow. The waves slow down over the plate and their wavelength shortens. Turn the plate at an angle to the wavefronts and they bend as they cross its edge. The concave plate shows a curved shallow region acting on the waves like a lens.
Diffraction through a gap. Set the two barriers in a line with a gap between them and run continuous waves from the motor. Narrow the gap step by step and watch the waves spread further beyond it. The lamp and motor both need a low-voltage supply such as a stepped power supply, since none is included.
Fit two point dippers to the ripple bar so that both touch the water, and run the motor. Circular waves spread from each dipper and overlap. Lines of calm water, where crests from one dipper meet troughs from the other, fan out between bands of strong ripples. Move the dippers closer together and the calm lines spread further apart. Raise the motor speed and they crowd closer together.
Use only a shallow layer, a few millimetres deep, and keep it even. Wave speed depends on depth, so a tank that is not level gives waves that change speed and wavelength as they cross it. Check the level before filling and pour the water in slowly.
Moving waves are hard to measure by eye. Spinning the hand stroboscope at the right speed makes the bands appear to stand still, so students can lay a ruler across the frozen pattern. The pattern also freezes at whole-number fractions of the wave frequency, so use the highest strobe rate that gives a single still pattern.
One wavelength is short and its edges are blurred, so a single reading carries a large error. Measure from one bright band to the tenth bright band beyond it, which spans ten wavelengths, and divide by ten. Repeat the measurement a few times and take the average.
Light from the lamp spreads out as it travels, so the image on the viewing surface is magnified. To correct for this, place a ruler of known length in the tank, measure the length of its shadow, and scale every wavelength reading by the same ratio.
Water waves travel more slowly in shallow water. The motor fixes the frequency, so the waves keep the same frequency over the plate. Since speed equals frequency times wavelength, a lower speed means a shorter wavelength. That change of speed is what bends the waves at an angled edge.
Common causes are a motor running too fast, vibration from the bench, water that is too deep, or a lamp set at the wrong height. Slow the motor, stand the tank on a firm table, reduce the water and adjust the lamp arm until the bands look sharp.
To request a quotation, send the product name, code and quantity through our contact page or add the item to your enquiry cart.
Last updated: 14 November 2026