- Physics Lab Equipment
- Chemistry Lab Equipment
- Biology Lab Equipment
- Anatomical Lab Equipment
- Learning
- Educational Lab Equipment
- Magnets
- Agriculture
- Astronomy
- Earth Science
- Geography Lab Equipment
- Safety Lab Coat
- Laboratory
- Meteorological
- Electricity & Magnetism
- Heat
- School Lab Equipment
- Lab Glassware
- Science Lab Equipment
- Tvet Lab Equipment
- Robotics Kits Supplier and Manufacturer for Schools India
- Math Lab Equipment Manufacturers and Exporters in Ambala
- STEM Kits Manufacturers and Supplier India
- Engineering Lab Equipment
- Hospital Lab Equipment
- Water, Sanitation & Hygiene Supplies
- Cold Chain, Solar & Communication Equipment
- Nutrition
Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P
Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P (Product Code: SLE/WDF/12) is a polypropylene clamp saddle used to take a ½-inch threaded service connection off a 110 mm HDPE water main without cutting the main. It clamps around the pipe, has a single middle outlet with a female thread for GI pipe and is rated for 10 bar at 20°C, which suits crews connecting tap stands and buildings. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.
Specifications
| Parameter | Detail |
|---|---|
| Fitting type | Clamp saddle connector for HDPE pipe, single middle outlet |
| Outside/nominal diameters | 110 mm (HDPE pipe) x ½" (GI pipe) |
| Outlet | Female thread for G.I. pipe |
| Material | Reinforced, high-impact-strength polypropylene, UV stabilised |
| Pressure rating | 10 bar at 20°C |
| Temperature range | 0 to 50°C |
| Product code | SLE/WDF/12 |
| Supplied by | Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India |
What Is the 110 mm HDPE Clamp Saddle Used For?
When a new house connection, tap stand or school water point has to be fed from an existing HDPE main, a clamp saddle is the least disruptive way to do it. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P closes around a 110 mm outside-diameter HDPE pipe, and the half-inch galvanised service line is then screwed into its female-threaded outlet.
Typical practice is to fit the saddle on a clean, undamaged section of pipe, tighten the clamp evenly so the seal seats squarely, and then drill the main through the outlet with a suitable cutter. Keep the water temperature within 0 to 50°C, and note that the 10 bar rating is stated at 20°C; plastic fittings generally carry less pressure as temperature rises, so allow a margin in hot climates. The UV-stabilised polypropylene helps where the saddle is exposed to sunlight at a tap stand or open valve box.
What to Specify When Ordering
- Main pipe: 110 mm outside diameter HDPE.
- Branch: ½" GI pipe with a male-threaded end.
- Number of service connections (one saddle per tapping).
- Expected water temperature and pressure, to confirm they fall within 0 to 50°C and 10 bar at 20°C.
Supplier
Jain Scientific Equipments Private Limited, trading as ScienceLab from Ambala, Haryana, supplies this polypropylene clamp saddle as part of a wider range of HDPE, PVC and GI water fittings. Better known as a laboratory equipment supplier in India, the company sources the item and prepares single quotations for projects that need pipe fittings, pumps and hygiene supplies from one vendor. More about the company appears on the ScienceLab profile page.
Related Water, Sanitation & Hygiene Supplies
Items used on the same HDPE main or on the service line leaving the saddle:
- T, PP comp, HDPE 110 x 110 x 110mm OD-P — a full-size branch where a half-inch tapping would be too small.
- Adaptor PP Comp, HDPE 110mmxmthd GI. 4"O/ND-P — joins the same HDPE main to 4" GI sockets at a line end or pump.
- Socket equal fthd GI ½" ND 14 Bar — extends the half-inch GI service pipe leaving the saddle.
- Tee 90° Equal fthd GI ½" ND 14 Bar — splits the service line to feed two taps.
Browse the Water, Sanitation & Hygiene Supplies category for the full range.
Frequently Asked Questions
What pipe sizes does the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fit?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P fits HDPE pipe of 110 mm outside diameter, and its outlet takes a half-inch nominal diameter GI pipe through a female thread. "O/ND" in the name stands for outside/nominal diameter.
What pressure and temperature is the saddle rated for?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is rated for 10 bar at 20°C, with a suitable temperature range of 0 to 50°C. At higher water temperatures a plastic fitting's pressure capacity generally falls, so allow a margin in warm conditions.
What material is the clamp saddle made of?
The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P is reinforced, high-impact-strength polypropylene that is UV stabilised. The UV stabilisation helps the saddle withstand sunlight where it is installed above ground or in an open valve box.
Does the main need to be cut to fit the saddle?
No. The Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P clamps around the existing 110 mm HDPE main, and the connection is made by drilling the pipe wall through the saddle outlet, so the main stays in one piece.
Who supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P?
Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, Haryana, supplies the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P. It sources the saddle and quotes it for water-network, institutional and project buyers in India and international markets.
Can the saddle be quoted with other HDPE fittings?
Yes, the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P can be quoted together with the other HDPE, PVC and GI fittings on your list. Send the complete schedule and delivery location through the contact page for one consolidated price.
Request a Quote
Count the service connections you plan and send that number with your enquiry for the Clamp Saddle PP, HDPE 110mm x fthd ½" O/ND-P through the contact page. You can also add the saddle to the enquiry cart together with the GI fittings for each service line.
Last updated: 24 September 2026
