- Physics Lab Equipment
- Chemistry Lab Equipment
- Biology Lab Equipment
- Anatomical Lab Equipment
- Learning
- Educational Lab Equipment
- Magnets
- Agriculture
- Astronomy
- Earth Science
- Geography Lab Equipment
- Safety Lab Coat
- Laboratory
- Meteorological
- Electricity & Magnetism
- Heat
- School Lab Equipment
- Lab Glassware
- Science Lab Equipment
- Tvet Lab Equipment
- Robotics Kits Supplier and Manufacturer for Schools India
- Math Lab Equipment Manufacturers and Exporters in Ambala
- STEM Kits Manufacturers and Supplier India
- Engineering Lab Equipment
- Hospital Lab Equipment
- Water, Sanitation & Hygiene Supplies
- Cold Chain, Solar & Communication Equipment
- Nutrition
Tee 90° Equal fthd GI ½" ND 14 Bar
Tee 90° Equal fthd GI ½" ND 14 Bar (Product Code: SLE/WDF/09) is a small-bore galvanised iron tee used to split a ½-inch threaded water line into two equal branches for taps, basins and other service points. All three outlets share the same ½" nominal diameter with internal threads, and the fitting is rated for 14 bar, making it a routine item for plumbers fitting out a school laboratory setup in India or a campus washroom. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India.
Specifications
| Parameter | Detail |
|---|---|
| Fitting type | 90° equal tee |
| Nominal diameter | ½" on all three outlets |
| Thread | Internal (female) thread |
| Material | Malleable cast iron |
| Finish | Hot-dip galvanised and threaded after galvanising |
| Pressure rating | 14 bar (200 lb/sq inch) |
| For use with | Galvanised iron water pipes |
| Product code | SLE/WDF/09 |
| Supplied by | Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India |
What Is the Half-Inch GI Equal Tee Used For?
Half-inch lines are the last stage of most water systems — the pipe that runs along a laboratory bench to its sink taps, feeds a row of wash basins or supplies a hand-wash point. The Tee 90° Equal fthd GI ½" ND 14 Bar lets one such line serve an extra outlet: water continues along the run and also leaves through the side branch at the same size.
Tighten small fittings with care, since over-tightening a half-inch joint strains the thread while too little torque leaves a weep. Wrap the male threads with sealing tape in the direction of the thread, start the pipe by hand, then finish with a wrench. Where several tees sit along a bench line, clip the pipe firmly between them so that repeated tap use does not work the joints loose.
What to Specify When Ordering
- The number of branch points on each line (one tee per take-off).
- Confirmation that the line is ½" nominal diameter GI pipe with male-threaded ends.
- Sockets, nipples or reducing fittings needed to reach each tap connection.
Supplier
Jain Scientific Equipments Private Limited trades as ScienceLab and supplies this half-inch tee, sourcing it for customers who need plumbing items alongside their laboratory or WASH orders. Quotations, packing and dispatch are handled from Ambala, Haryana. For vendor registration and export paperwork, the supplying company's details are IEC AAECJ8618A (DGFT) and GSTIN 06AAECJ8618A1ZT. Background on the business is on the ScienceLab company profile.
Related Water, Sanitation & Hygiene Supplies
Small-bore GI fittings that complete a tap or basin line:
- Socket equal fthd GI ½" ND 14 Bar — joins two lengths of half-inch pipe on the same line.
- Socket Reduction fthd ¾" x ½" ND 14 Bar — steps a three-quarter-inch feed down to the half-inch line the tee sits on.
- Cap fthd GI 14 Bar — closes the far end of a line; confirm the size with us.
- Plug Hollow mthd GI 14 Bar — seals a branch left ready for a future tap.
View every item in the Water, Sanitation & Hygiene Supplies category.
Frequently Asked Questions
What size is the Tee 90° Equal fthd GI ½" ND 14 Bar?
The Tee 90° Equal fthd GI ½" ND 14 Bar is half-inch nominal diameter on all three outlets, each with an internal female thread. As an equal tee, its branch is the same size as the run, so it suits standard half-inch service lines.
What pressure is the half-inch GI tee rated for?
The Tee 90° Equal fthd GI ½" ND 14 Bar is rated for 14 bar, equivalent to 200 lb per square inch. Check this rating against the pressure of your pump, overhead tank or mains supply before installation.
Can this tee be used on a laboratory bench water line?
Yes, the Tee 90° Equal fthd GI ½" ND 14 Bar can branch a half-inch galvanised supply line to feed extra taps or sinks on a laboratory bench, provided the rest of the line is half-inch GI pipe with male-threaded ends.
What are the tee's material and coating?
The Tee 90° Equal fthd GI ½" ND 14 Bar is malleable cast iron with a hot-dip galvanised coating, and its threads are cut after galvanising. The zinc layer protects the body from rust, while threading afterwards keeps the threads clean.
Who supplies the Tee 90° Equal fthd GI ½" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd (ScienceLab), based in Ambala, Haryana, supplies the Tee 90° Equal fthd GI ½" ND 14 Bar. The company sources the fitting and can quote it with other plumbing and WASH items for customers in India and international markets.
Can small quantities be ordered, or only bulk?
Both small and bulk requirements for the Tee 90° Equal fthd GI ½" ND 14 Bar can be sent for quotation. State the exact quantity and delivery location on the contact page, and the reply will confirm what can be supplied.
Request a Quote
Put the Tee 90° Equal fthd GI ½" ND 14 Bar in the enquiry cart with the other half-inch fittings for your installation and submit the list, or write to us through the contact page with quantities and the delivery location.
Last updated: 24 September 2026
