- Physics Lab Equipment
- Chemistry Lab Equipment
- Biology Lab Equipment
- Anatomical Lab Equipment
- Learning
- Educational Lab Equipment
- Magnets
- Agriculture
- Astronomy
- Earth Science
- Geography Lab Equipment
- Safety Lab Coat
- Laboratory
- Meteorological
- Electricity & Magnetism
- Heat
- School Lab Equipment
- Lab Glassware
- Science Lab Equipment
- Tvet Lab Equipment
- Robotics Kits Supplier and Manufacturer for Schools India
- Math Lab Equipment Manufacturers and Exporters in Ambala
- STEM Kits Manufacturers and Supplier India
- Engineering Lab Equipment
- Hospital Lab Equipment
- Water, Sanitation & Hygiene Supplies
- Cold Chain, Solar & Communication Equipment
- Nutrition
Tee Reduction fthd GI 2½" x 2" ND 14 Bar
Tee Reduction fthd GI 2½" x 2" ND 14 Bar (Product Code: SLE/WDF/08) is a galvanised iron reducing tee used to take a smaller 2-inch branch off a 2½-inch threaded water main in pressurised supply networks. The side outlet is reduced to 2" while the run stays at 2½", all three ends are internally threaded, and the fitting is rated for 14 bar. It is supplied by Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India, for water-supply and institutional projects.
Specifications
| Parameter | Detail |
|---|---|
| Fitting type | 90° tee, reducing on the side (branch) outlet |
| Nominal diameters | 2½" x 2" |
| Thread | Internal female parallel thread |
| Material | Malleable cast iron |
| Finish | Hot-dip galvanised, threaded after galvanising |
| Pressure rating | 14 bar (200 lb/sq inch) |
| For use with | Galvanised iron water pipes |
| Product code | SLE/WDF/08 |
| Supplied by | Jain Scientific Equipments Pvt Ltd (ScienceLab), Ambala, India |
What Is the GI Reducing Tee Used For?
Distribution lines often step down in size as they branch: the main carries the full flow while each branch serves a smaller building, tap stand or storage tank. The Tee Reduction fthd GI 2½" x 2" ND 14 Bar does this in one fitting — the main passes straight through at 2½" and the branch leaves at a right angle in 2" — so no separate reducing socket or bush is needed at the junction.
Install it with the straight run in line with the main and the reduced outlet pointing toward the branch. Because the internal threads are parallel, prepare each male pipe end with sealing tape or jointing compound before tightening. Where a branch may need isolating for repairs, plan a valve on the 2" side close to the tee, and pressure-test the finished network within the 14 bar rating.
What to Specify When Ordering
- Confirmation that the main is 2½" and the branch 2" nominal diameter GI pipe.
- The number of tees, usually one for each branch take-off.
- Working and test pressure of the network, so it stays within 14 bar.
- Any straight fittings needed in each size, such as sockets or nipples.
Supplier
ScienceLab, the trading name of Jain Scientific Equipments Private Limited, supplies this reducing tee from Ambala, Haryana as part of its range of water, sanitation and hygiene items. The company sources the fitting and answers each enquiry with a quotation that can bundle every fitting on a project's bill of quantities. Institutions that buy through laboratory equipment tenders in India sometimes include water-supply works as well, and this tee can be priced within the same response. More about the company is on the ScienceLab profile page.
Related Water, Sanitation & Hygiene Supplies
Other threaded GI items used when laying out branch lines:
- Tee 90° Equal fthd GI ½" ND 14 Bar — an equal tee for small-bore service branches further along the network.
- Socket Reduction fthd ¾" x ½" ND 14 Bar — steps smaller service lines down in size.
- Nipple Taper mthd Hex GI 14 Bar — a male-threaded connector for joining the tee to other female fittings; confirm the size you need.
- Plug Hollow mthd GI 14 Bar — closes the branch outlet until the branch line is laid.
The complete range is in the Water, Sanitation & Hygiene Supplies category.
Frequently Asked Questions
Which outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is reduced?
The side (branch) outlet of the Tee Reduction fthd GI 2½" x 2" ND 14 Bar is the reduced one, at 2-inch nominal diameter, while the straight run is 2½ inch. All three ends are internally threaded to take male GI pipe.
What pressure rating does the reducing tee have?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is rated for 14 bar (200 lb per square inch). The rating applies to the fitting itself, so confirm that the pipes, valves and other fittings on the same network are rated for at least the same pressure.
What is the tee made from?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar is malleable cast iron, hot-dip galvanised to resist corrosion in water service. Its parallel female threads are cut after galvanising, so the thread form stays clean and engages the pipe properly.
Why use a reducing tee instead of an equal tee and a reducer?
The Tee Reduction fthd GI 2½" x 2" ND 14 Bar branches and reduces in one fitting, which gives fewer threaded joints, a shorter assembly and fewer possible leak points than an equal tee combined with a separate reducing socket or bush.
Who supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar?
Jain Scientific Equipments Pvt Ltd, which trades as ScienceLab from Ambala, Haryana, supplies the Tee Reduction fthd GI 2½" x 2" ND 14 Bar. It sources the fitting and quotes it for institutional, contractor and project buyers in India and international markets.
What details speed up a quotation?
For a quick quotation on the Tee Reduction fthd GI 2½" x 2" ND 14 Bar, give the quantity, the delivery location and a list of the other fittings on the job. Questions about documentation for the fitting can be raised on the contact page before ordering.
Request a Quote
Add the Tee Reduction fthd GI 2½" x 2" ND 14 Bar to the enquiry cart, or describe your branch layout on the contact page. We will reply with a quotation covering the tees and any related fittings you list.
Last updated: 24 September 2026
