, Resuscitation and Anaesthesiology Equipment Manufacturer,Supplier and Exporter in India,Resuscitation and Anaesthesiology Equipment Manufacturer

Science Lab Export, Anaesthesia and resuscitation refers to a speciality practiced in the operating theatre (anaesthesia) and/or in a specialised resuscitation unit. Science Lab Export Inpatients presenting signs of failure of at least two of the following vital functions are taken to a resuscitation unit: Respiratory system (lungs), Circulatory system (heart and vessels), Renal function, Nervous system, etc.
Resuscitation helps to keep patients with severe deficiencies alive. These patients benefit from being constantly monitored in this specialised unit.
Anaesthesia is performed in the operating theatre in close collaboration with surgeons. This may be general anaesthesia, which puts the patient in a state of unconsciousness, in particular to limit movement and pain during surgical procedures, or loco-regional anaesthesia, where only a specific part of the body is numbed. Resuscitation and Anaesthesiology Equipment Manufacturers, Suppliers and Exporters in Ambala India, Resuscitation and Anaesthesiology Equipment Manufacturers in Ambala India, Hospital Lab Equipment Manufacturer in Ambala India

Adult Resuscitator Hand Operated Set

Product Code : SLE/RAE/01

Specifications:
Resuscitator operated by hand.
Ventilation with ambient air.
Resuscitator to ventilate adult (body weight over 30kg).
All parts must be manufactured from high-strength, long-life materials and require no special maintenance or storage conditions.
Resuscitator shall be easy, to disassemble and reassemble, to clean and disinfect, and be autoclavable.

Materials: Latex-free
Compressible self-refilling ventilation bag: silicone rubber.
Oxygen reservoir bag: plastic.
Inlet valve with nipple for O2 tubing: polycarbonate/polysulfone
Masks: transparent silicone rubber.
Non-rebreathing patient valve with pressure limiting valve: polycarbonate/polysulfone/silicone.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school lab equipment supplier, school lab equipments, school lab equipments export, school lab equipments exporter, school lab equipments manufacturers, school lab equipments manufacturers in india.

Suction Pump Foot Operated Single Piston

Product Code : SLE/RAE/02

Specifications:
Piston, with diaphragm valve, is sealed with removable elastic O-ring
Pedal movement generates suction every time it’s depressed
High performance, high quality, single piston portable foot-operated suction pump
For pharyngeal and tracheal aspiration, and other minor medical procedures
Integrated spring, returns the pedal to its initial ready-to-use position
Lever minimises pedal force required to reach maximum flow
For operator’s comfort, pedal should support at least 20 cm of the foot, and distal-end displace maximum 9-11 cm
Large stable base is entirely fit with anti-slip, preventing the pump from gliding-away while in use
Air-flow, maximum: 30 to 40 L/min (such as at two pumping strokes per second)
Container is transparent, allowing assessing collected volume
Wide opening at the top of the container allows for easy and thorough cleaning
Collection capacity container: 900-1100 ml
Operating temperature range: -20 C to +50 C
The suction pump set can be entirely disassembled, facilitating proper cleaning and disinfection
All parts can be autoclaved at 121 C
Vacuum, maximum: - 70 kPa (ca. - 700 mbar)
Basic essential design without manometer

Materials:
Piston O-ring: Teflon or equivalent
Foot pedal: aluminium or equivalent sturdy plastic, fit with embossed anti-slip relief
All parts are manufactured from high-strength, durable material, not requiring specific maintenance or storage conditions
Container: transparent polycarbonate or equivalent sturdy transparent plastic
Conical suction tip: Acetal or equivalent tough plastic
Aspirating tube: silicone rubber
Bottom: rubber or equivalent anti-slip material
Gasket, O-rings and valve diaphragm: silicone rubber or equivalent.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school educational lab equipments manufacturers, school lab equipment export, school lab equipment exporter, school lab equipment manufacturer, school lab equipment manufacturers, school lab equipment manufacturers in india.

Laryngoscope Child / Adult Set

Product Code : SLE/RAE/03

Specifications:
Handle made of either chromium-plated or stainless steel
Large hollow, cylindrical, slightly ribbed handle
Stud contact, fitting various sizes and types of depressors
Can be opened to insert two batteries (type LR14, size C, 1.5 V)
With a set of four stainless steel depressors, with halogen bulb

Miller type:
Straight Nr 1, length approx. 100 mm

Maclntosh type:
Curved Nr 2, length approx. 110 mm
Curved Nr 3, length approx. 135 mm
Curved Nr 4, length approx. 155 mm

Instructions for use:
It is recommended to remove the batteries when the instrument is stored for a long time.
To assist endotracheal intubation of adults and infants during anesthesia or resuscitation.
The stainless steel parts can be sterilized; the light bulb and batteries should be removed.
Depressors and bulbs must be carefully washed and disinfected after each used.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school science equipments suppliers, school science kits, school science lab equipment exporter, school science lab equipment manufacturer, school science lab equipment supplier, school science lab equipment suppliers.

Guedel Airway Sterile Single Use

Product Code : SLE/RAE/04

Specifications:
Material
: Polyethylene/vinyl acetate (EVA) - Polyvinyl chloride (PVC).
Sterile, single patient use.
Semi-rigid, transparent.
Oro-pharyngeal airway, Guedel type.
Proximal (or buccal) end straight and reinforced.
Flange colour coded and/or marked with corresponding size number.
Initial sterilisation method:
Ethylene oxide gas or gamma radiation.
Size: Airway Guedel, size 2, Length approximately 70mm.

Instructions for Use
Used in emergency care for short term airway management or for use during anesthesia.
An airway adjunct used for the purpose of maintaining patency of a patient’s airway, preventing the tongue from covering the epiglottis.
Correct size selected by measuring the distance between the first incisors and the angle of the jaw.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school science lab equipment suppliers in india, school science lab equipments exporter, school science lab equipments manufacturers,school science lab equipments manufacturer, school science lab equipments supplier, school science lab equipments suppliers.

Disposable Endotracheal Tube With Cuff Sterile

Product Code : SLE/RAE/05

Specifications:
Material: Polyvinyl chloride (PVC).
Disposable.
Endotracheal tube shall meet the standards concerning the dimension, the tube, the point, the cuff and the marking.
Endotracheal tube with:
Open distal end and Magill-type point with oral angle of 37.5º.
Cuff located near the distal end: Low pressure cuff, inflating system with valve and Luer tip connector.
Radio opaque mark.
Initial sterilisation method: Ethylene oxide gas or Gamma radiation.
Standard connector (ext. Ø 15mm) at the proximal end enabling the tube to be connected to the ventilation system.
With Murhpy's eye.
Sterile.
Graduations.
Size: Ø internal 8mm.

Instructions for use:
Device designed to be introduced into the trachea via the mouth or nose in order to link the trachea (upper respiratory tract) to the outside air, giving the possibility to provide ventilation assistance to patient (manual or mechanical).
Sterile Endotracheal tube:
Device used to correct a deficiency in respiratory function during general anaesthesia or resuscitation.
Intended for endotracheal tubes for adults or children depending the diameter.
Lubricate the distal end and cuff of the endotracheal tube (ETT) and the distal 1/2 of the Endotracheal Tube Introducer (Bougie)
Inserting the endotracheal tube must be done only by staff trained in resuscitation practice.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school science lab equipments suppliers in india, school science lab instruments, school science lab instruments exporter, school science lab instruments manufacturer, school scientific equipments, science educational equipment.

Disposable Endotracheal Tube Without Cuff Sterile

Product Code : SLE/RAE/06

Specifications:
Material: Polyvinyl chloride (PVC).
Disposable.
Graduations.
Endotracheal tube shall meet the required standards describing the dimensions, the tube characteristics, tube point and the tube markings.
Endotracheal tube with:
Open distal end and Magill-type point with oral angle of 37.5º.
Standard connector (ext. Ø 15mm) at the proximal end enabling the tube to be connected to the ventilation system.
With Murphy's eye.
Sterile.
Initial sterilisation method: Ethylene oxide gas or Gamma radiation.
Endotracheal tube without cuff.
Size: Ø internal 3.5mm.

Instructions for use:
Sterile Endotracheal tube:
Device used to correct a deficiency in respiratory function during general anaesthesia or resuscitation.
Inserting the endotracheal tube must be done only by staff trained in resuscitation practice.
Device designed to be introduced into the trachea via the mouth or nose in order to link the trachea (upper respiratory tract) to the outside air, giving the possibility to provide ventilation assistance to patient (manual or mechanical).
Lubricate the distal end of the endotracheal tube and the distal 1/2 of the Endotracheal Tube Introducer (Bougie)
Intended for endotracheal tubes for adults or children depending the diameter.


Contact Science Lab for your Educational School Science Lab Equipments. We are best science educational equipments, science educational instruments, science lab equipments manufacturer, science laboratory instruments exporter, scientific educational equipments, scientific educational lab equipment.

Adult Nasal Prong Oxygen Single Use

Product Code : SLE/RAE/07

SPECIFICATIONS
Nasal cannula (nasal prongs), device designed for easy administration of oxygen into the patient nose through two small prongs placed in the nostrils, providing comfort for the patient.

The device consists of:
Material: Preferably soft and kink resistant polyvinyl chloride (PVC).
Soft twin prongs nasal tips to ensure equal oxygen flow to both.
Soft funnel shaped connector to facilitate easy connection to oxygen source.
Adjustable, smoothly finished nasal tips for maximum patient comfort.
Length of the oxygen tube: +/-2 m.
Single use.
Non-sterile.
Star lumen main tube to avoid accidental blockage.
Over-the-Ear tubing adjustable
Size selected: Adult

INSTRUCTIONS FOR USE:
Care should be taken to keep the nostrils clear of mucus, which could block the flow of oxygen.
Nasal cannula used to deliver oxygen directly to the patient via two small prongs placed in the nostrils
Place the twin prongs inside the nostrils and secure them with a piece of tape on the cheeks near the nose and adjust the harness (Over-the-Eartubing).
It is important to have the proper equipment to control low flow rate.
Set a flow rate of 1-2 l/min (0.5 l/min for young infants) to deliver an inspired oxygen concentration of 30-35%.
Humidification is not required with nasal prongs.

Contact Science Lab for your Educational School Science Lab Equipments. We are best scientific educational lab equipments, scientific equipments manufacturers, scientific lab equipment manufacturers, scientific lab plasticware, scientific laboratory equipment manufacturer, scientific laboratory equipment supplier.
 

Neonatal incubator Automatic With Accessories

Product Code : SLE/RAE/08

DESCRIPTION:
Neonatal incubator, double-wall, electronic, automatic, mobile, with accessories

TECHNICAL SPECIFICATIONS:
Sturdy construction, mobile base with 4 anti-static swivel castors and 2 brakes
Protective side/corner bumpers
Double-wall neonatal incubator, mobile
Automatic servo-control and manual control
Mould and corrosion resistant frame
Suitable for frequent and easy dismantling and cleaning
Side rails, IV pole and instrument shelf
Cabinet with 2 drawers, integrated in the base
Side handles for easy moving

Canopy:
Inclined front, with access door and 2 port holes
2 rear port holes
double-wall
radio-transparent
4 (min) apertures for cables and tubing
Silent incubator and door / port holes operation
Dimensions 45 W x 80 L x 43 H cm (minimum guaranteed)

Mattress:
fixed mattress tray
tilting ± 12 degrees

Modes:
Servo-controlled, air temperature
Servo-controlled, skin temperature
Manual

Skin temperature sensor accuracy ± 0.3 ºC
Humidifier with integrated water chamber, passive not-adjustable (evaporation chamber) or servo-controlled adjustable humidifying system (up to 95 % relative humidity) depending on the available incubator model
Air temperature setting 25 – 37 ºC, override up to 39 ºC, with 0.1 ºC increments
Temperature variability (fluctuation between set and real values) ± 0.5 ºC
Temperature uniformity (at mattress level) < 0.8 ºC
Skin temperature setting 34 – 36 ºC, override up to 38 ºC, with 0.1 ºC increments
Warm-up time (to 37 ºC in 22 ºC ambient temperature) < 30 min
Air velocity over the bed < 0.35 m/s
Automatic self-test and continuous system monitoring
Control panel and display, visualisation of settings and measured parameters
Audio-visual alarms for skin/air temperature, sensors, fan, heater, system functionality
Air filter capacity at inlet 99 % particles > 0.5 um
Power requirements 110 – 220 V / 50 – 60 Hz
Power consumption 600 – 750 W
Noise level inside the incubator < 55 dB

Contact Science Lab for your Educational School Science Lab Equipments. We are best scientific laboratory equipments manufacturer, scientific laboratory equipments supplier, technical educational equipment exporter, technical educational equipment manufacturer, technical educational equipment supplier, technical educational equipments exporter.

Newborn Warmer System Basic

Product Code : SLE/RAE/09

DESCRIPTION:
Neonatal warming system, nest-type with water mattress and heating pad, portable, basic set

TECHNICAL SPECIFICATIONS:
Integrity testing of all system parameters every 5 minutes.
Flexible waterproof low voltage heating pad slides under mattress.
Pre-set is 37°C, Adjustable from 35 to 38°C in increments of 0,1°C.
The Warmer is used to assist premature babies maintaining the appropriate body temperature.
System consists of a control unit, a heating pad, a water mattress and an inflatable BabyNest frame.
Electronic servo temperature control.
Perform self-testing of all functions and internal safety circuit by switching the control unite.
Accuracy temperature control of heating pad is ±0.1°C.
Automatic warm-up to 37°C, time to stabilize approx. 20 min (starting at 20°C). (Warm up time is shortened if water mattress is filled with lukewarm water at start).
Large colour display shows operational status, with set and measured values.
Over Temperature Alarm: at a water temperature of 39.5 ±1 °C. Warming capacity: About 4-5°C per hour. (Room temperature about 22°C and filled with 4,5 liters of water and placed on the mattress of a baby bed and covered with the nest and a sheet. Connection to mains or a 24V battery.)
Strong soft plastic BabyNest mattress fills with water (about 36°C), approx. 4.5 L.
Reusable BabyNest frame keeps baby in place.
Cotton cover frame can be tightly secured around the water mattress and heating pad.
The water mattress will cool 1°C per hour which means that one has about 2 hours to restore power.
External battery connection point at the underside of the control unit.

Heating Pad:
Material
: PVC.
Voltage: 24-volt DC from control Unit BW-50 007 when powering with mains power or 24V DC when powering from 12-24V battery source.
Power requirements: 110-240 V AC or 110-120 V AC.
Battery 12 or 24 V.
Power consumption 50 Watt. (10 Watt when the Control Unit is powered from a 12 Volt battery)
Frequency 50 or 60 Hz,

Baby Nest:
Material: Cover, high quality cotton and polyester.
Washing: Recommended temperature 60°C, can tolerate 90°C but might shorten lifetime.

Water Mattress:
Material
: Medical Grade PVC.

Control Unit:
Temperatures available: 35 to 38°C increments of 0.1°C.
Auditory Alarm: 55 dB sound level.
Main Power/frequency: 110-240 V AC or 110-120 AC. 50/60 Hz.
Battery power: 24 V DC, 12 V DC (with limited warming capacity)
Internal Battery: Alkaline, 1.5V size LR6 (AA) (only for power failure alarm.
Indication of temperatures and alarms:
Over temperature alarm at water Temperature of 39.5 ±1 °C.

Contact Science Lab for your Educational School Science Lab Equipments. We are best technical educational equipments manufacturers, technical educational equipments manufacturer, technical educational equipments supplier, technical educational instruments, technical educational instruments exporter, technical educational instruments manufacturer, vocational training lab instruments exporter.

Defibrillator Basic With Accessories

Product Code : SLE/RAE/10

DESCRIPTION:
External defibrillator for adult and paediatric patients, with ECG monitor and printer, synchronised and bi-phasic, portable, AC and battery powered, with accessories.

TECHNICAL SPECIFICATIONS:
Suitable for adult and paediatric patients
Supplied with adult and paediatric pads/adapters
External defibrillator with ECG monitor
Non-directional pads, suitable for bi-phasic impulse waveform

Defibrillator features:
Patient resistance 30 – 175 Ohm (minimum guaranteed range)
Load compensation, energy level automatic adjustment to the patient impedance
Manual and synchronised defibrillation
bi-phasic energy waveform
Energy output accuracy ± 15 %
Adult and paediatric energy settings
Energy output range 2 – 200 J or 2 – 360 J.
Adjustable energy output, by steps
Charge time to maximum energy < 10 s (mains power supply and battery charged)

ECG monitor:
ECG gain 2.5, 5, 10 and 20 mm/mV (minimum guaranteed)
Protection against defibrillation discharges
Detection through pads or dedicated ECG cable
ECG waveform and analysis, selectable visualisation modes
3-leads ECG cable
Adjustable ECG print modes and settings (real-time, manual)

Printer:
Paper width 58 or 72 mm, depending on the available model
Internal safety discharge feature 
Built-in 3-channel thermal printer
Print of ECG curves and analysis, events, settings and alarms
Paper speed 25 mm/s 
Compatibility with additional modes and monitoring features, not included (SAED, AED and pace modes, SpO2)

Internal storage for ECG, events (at least 500 or 60 min monitoring) and parameters
Integrated control panel with all parameters and controls
Display, backlit flat panel, 5 – 8 inch 
Data/USB communication interface
Audio/visual alarms for pads connection, mains/battery power supply status, paper and printer status, system errors
Automatic and manual self-test, continuous check of pads and electrodes connection
Visualisation of defibrillation mode, energy, ready/charging state, ECG curves and heart rate, date/time, settings, mains and battery status, system messages and alarms
Automatic switch to battery in case of power failure, automatic recharge on connection to mains
Integrated battery charger and transformer
Integrated carry handle
Splash and shock resistant
Power requirements 110 – 220 V / 50 – 60 Hz
Power consumption 200 W
Removable rechargeable battery
Battery autonomy > 100 shocks at 200 J or 3.5 h monitoring

Contact Science Lab for your Educational School Science Lab Equipments. We are best school lab equipment supplier, school lab equipments, school lab equipments export, school lab equipments exporter, school lab equipments manufacturers, school lab equipments manufacturers in india.
 

Nebulizer Electric With Accessories

Product Code : SLE/RAE/11

DESCRIPTION
Nebulizer Compressor-driven, portable, AC powered with accessories

TECHNICAL SPECIFICATIONS
Integrated drug reservoir, capacity 2 - 6 ml, residual volume: 2 ml
Median Mass Aerodynamic Diameter (MMAD) of particles: 2.44 – 3.16 µM
Portable, compressor-driven nebulizer, for the treatment of upper/lower respiratory system and for the delivery of nebulized drugs
Maintenance-free and oil-free compressor pump
Air inlet filter
Noise level: ≤ 55 dB
Power requirements 220 V / 50 Hz
Sturdy construction, suitable to be disinfected with hospital-grade products
Device is provided with accessory storage compartment
Air flow under load: 5 – 6 l/min
Drug nebulization flow 0.2 – 0.4 ml/min 
Power consumption: ≤ 170 W

OPERATING ENVIRONMENT
Operating conditions: 10 - 40°C / 90% relative humidity
Storage conditions: 0 - 50°C / 90% relative humidity

Contact Science Lab for your Educational School Science Lab Equipments. We are best school lab equipments supplier, school lab export, school lab exporter, school laboratory equipment manufacturers, school laboratory equipment suppliers, school science equipments.

Oxygen Concentrator

Product Code : SLE/RAE/12

Oxygen Concentrators are not suitable to be used as an oxygen source to other medical equipment providing respiratory support, such as ventilators, CPAP devices, High Flow Nasal Oxygen, etc.

SPECIFICATIONS:
Provides continuous flow of concentrated oxygen 93%
Oxygen sensing device is integrated and measures concentration at flow meter entrance.
Device concentrates oxygen from ambient air
On 4 antistatic swivel castors, 2 with brakes
Integrated handle allows for easy moving and positioning
Flowmeter range: 1 to 10 LPM
Flowmeter continuously adjustable with markings at 0.5 L intervals
Continuous monitoring, with visual and audible alert on:
Low/ high output pressure, no flow, low oxygen concentration <82%, power failure
Sound level produced: less than 52 dB (A)
Maximum output flow: 10 LPM
Output pressure: min 55 // kPa. 0.04/0.07
Power requirements: 220V-240V, 50Hz-60Hz or 110V 50/60Hz
Digital or analogue meter to display cumulative hours of device operation
User interface easy to operate with numbers and displays that are clearly visible
Device weight: 28 kg
Oxygen outlet durable, with approx.6mm barbed fitting or equivalent

ENVIRONMENTAL CONDITIONS
Storage conditions: e: -40 °C to 55°C / RH: ≤ 95%
Operating altitude: 0 to 2286m above sea level
Operating conditions: 10 to 40°C / RH: 15 to 85%

Contact Science Lab for your Educational School Science Lab Equipments. We are best school science equipments suppliers, school science kits, school science lab equipment exporter, school science lab equipment manufacturer, school science lab equipment supplier, school science lab equipment suppliers.

Resuscitation Table Newborn With Accessories

Product Code : SLE/RAE/13

DESCRIPTION:
Neonatal resuscitation table, mobile, with warmer and accessories

SPECIFICATIONS:
Side handle for easy moving
Integrated support for 2 x 10 l oxygen cylinders
Side rail and IV pole for mounting accessories and equipment
Mobile resuscitation table for neonatal patients, with warmer
Sturdy construction, with 4 anti-static swivel castors and 2 brakes
Side panels, transparent acrylic resin, collapsible/foldable for complete accessibility
Vertical column with controls and display
With lower drawer for storage

Table:
Mattress cover flame-retardant, waterproof and cleanable with
Surface 60 W x 76 L cm (minimum guaranteed dimensions)
Hospital-grade disinfection products
Mattress covering the entire table surface, thickness 5 cm

Heating system:
Reflector and safety grid
Integrated cradle heating
Overhead radiant heater, fixed height
Radiant heating by quartz/ceramic elements, parabolic
Uniform heat distribution

Lighting system:
With 2 x halogen additional spot examination lights
Integrated in the overhead radiant heater

Modes:
Pre-warming function
Instant switch between manual and servo modes
Servo-controlled, electronic and driven by skin temperature
Manual
Skin temperature setting 34 – 38 ºC, with 0.1 ºC increments (servo mode)
Skin temperature sensor accuracy ± 0.3 ºC
Power requirements 220 V / 50 Hz
Displayed parameters: mode (manual or servo), heating power (%), pre-set temperature, actual skin temperature, air temperature in the cradle
Audio-visual alarms for skin temperature, heating system and sensors failure
Display panel, integrated in the column, visualising working parameters and alarms
Power consumption 1,100 W
Manual and pre-heating settings 10 – 80 % by 10 % steps


Contact Science Lab for your Educational School Science Lab Equipments. We are best school science lab equipment suppliers in india, school science lab equipments exporter, school science lab equipments manufacturers,school science lab equipments manufacturer, school science lab equipments supplier, school science lab equipments suppliers
 

Infusion Pump With Accessories

Product Code : SLE/RAE/14

DESCRIPTION:
Infusion pump, volumetric, single channel, AC and battery powered, with accessories

SPECIFICATIONS:
Suitable for rail and IV pole mount
Programmable infusion by volume, time and flow-rate
Infusion pump, volumetric, portable, for IV fluids infusion, single channel
Peristaltic pump, continuous delivery
Flow-rate range 1 – 1,200 (minimum guaranteed) ml/h, 1 ml/h step, accuracy ± 5 %
Open system, compatible with commercial infusion sets
Battery autonomy > 5 h (at 30 ml/h)
Air bubble detection
Bolus program, range 100 – 900 ml/h
Volume limit range 1 – 9,999 ml, 1 ml step
KVO program, 1 ml/h for infusion rate < 10 ml/h and 3 ml/h for infusion rate > 10ml/h
Occlusion detection
Automatic self-test function
Battery and AC powered, with automatic switch between modes and automatic recharge when connected to mains
Power consumption 25 W
Integrated battery charger
Sturdy construction, splash- and shock-proof, plastic enclosure
Power requirements 110 – 220 V / 50 – 60 Hz
Display and control panel with visualisation of all working parameters (program, volume, flow, time) and system messages
Audio/visual alarms, with silencing feature, for: occlusion, air-in-line, door open, status and end of infusion/program, battery/power supply status and failure, system errors.

Contact Science Lab for your Educational School Science Lab Equipments. We are best school science lab equipments suppliers in india, school science lab instruments, school science lab instruments exporter, school science lab instruments manufacturer, school scientific equipments, science educational equipment

Portable Patient Monitor With Accessories

Product Code : SLE/RAE/15

DESCRIPTION:
Patient vital signs monitor, 5 physiological parameters, for adult ,paediatric/infant and neonatal patients, AC and battery powered, with a ccessories

SPECIFICATIONS:
5-parameters monitoring: ECG and Heart Rate (HR), Respiratory Rate (RR), SpO2, NIBP and Temperature
Portable vital signs monitor, suitable for adult, paediatric andneonatal patients

ECG and HR:
accuracy ± 1 bpm or ± 1%, whichever is greater
3-leads ECG, I-II-III selection (optional 5-leads I, II, III, aVR, aVL ,aVF, V)
waveform visualisation
S-T detection, arrhythmia analysis
standardising marker -1 to 1 mV or -2 to 2 mV (depending on the available model)
HR 15 – 300 bpm for adult and 15 – 350 bpm for paediatric/neonatal
gain 1.25, 2.5, 5, 10, 20, 40 mm/mV and Auto
sweep speed 6.25, 12.5, 25 and 50 mm/s

Respiratory rate (RR):
Resolution 1 rpm
Accuracy ± 2 rpm or ± 2% in the range 7 – 150 rpm, whichever is greater
RR range 0 – 120 adult, 0 – 150 paedriatric/neonatal

NIBP:
Measurement overall ranges (min. value diastolic, max. value systolic)
Oscillometric step deflation
Adjustable inflating pressure
10 – 270 adult, 10 – 200 paediatric, 10 – 135 neonatal
Systolic, diastolic and mean pressure measurement
Resolution 1 mmHg

SpO2:
Resolution 1%, accuracy ± 2% in the range 70 – 100 %
Range 0 – 100%
Heart rate detection 25 – 250 bpm, accuracy ± 3 bpm or ± 2%, whichever is greater

Temperature:
resolution ± 0.1 ºC
range 0 – 50 ºC
accuracy ± 0.1 ºC

Adjustable signal amplitude and sensitivity
TFT colour display > 10.4 inches
Audio-visual alarms and silencing feature for all monitored parameters
Display reports alarms, system errors, leads and sensors failure and AC/battery status
Multi-waveform and parameters visualisation, at least 4 channels
Defibrillator sync and protection
Trend display > 120 hours at 1 min resolution
Data and network interface
Robust design for use in demanding environment
Pacemaker detection/rejection
Patient information and trend internal database
Power requirements: 100 - 220 V / 50 Hz
Soft touch keys, durable and easy to clean surface, resistant tohospital-grade cleaning products
Automatic self-test and continuous system monitoring
Built-in rechargeable battery, autonomy > 3.5 hours
Automatic switch to battery in case of power failure, automatic recharge on connection to mains
Suitable for standard bed/wall rail and pole stand mount.

Contact Science Lab for your Educational School Science Lab Equipments. We are best scientific laboratory equipments manufacturer, scientific laboratory equipments supplier, technical educational equipment exporter, technical educational equipment manufacturer, technical educational equipment supplier, technical educational equipments exporter.

Venturi Face Mask Adult Single Use

Product Code : SLE/RAE/16

DESCRIPTION
Face mask to provide oxygen at flow rates between 1 – 10 LPM. Allows for precise oxygen delivery by utilizing different sized port to change FiO2 (24 – 50%). Also known as air-entrainment masks able to provide total inspiratory flow at a specified FiO2.

SPECIFICATIONS
Material: mask and tubing made from medical grade PVC
The mask has an adjustable nose clip and an adjustable strap to esnure the mask can be fitted securely.
Length of the oxygen tube: 1.5 to 2.1m
It delivers oxygen, with a specific concentration from 24% to 50% minimum "
The kit of the mask includes the tubing, humidity cup and multiple jets, which are color-coded and indicating the percentage of oxygen.
Single use, non-sterile item.
Adult size
FiO2 ranges 24% (4 LPM), 28 % (4 LPM), 31% (6 LPM), 35% (8 LPM), 40% (8 LPM), 50% (10 LPM
Anti-crush tubing is terminated with a “standard” connector

ENVIRONMENTAL CONDITIONS
Storage conditions: 0 to 50 deg. C, 10 to 90% relative humidity, non-condensing
Operating conditions: 5 to 40 deg. C, 10 to 90% relative humidity, non-condensing

Contact Science Lab for your Educational School Science Lab Equipments. We are best technical educational equipments manufacturers, technical educational equipments manufacturer, technical educational equipments supplier, technical educational instruments, technical educational instruments exporter, technical educational instruments manufacturer, vocational training lab instruments exporter.

Flow Splitter For Oxygen Concentrator

Product Code : SLE/RAE/17

DESCRIPTION:
Flow splitter for oxygen delivery, 5 outlets and 1 inlet, with independent flowmeters

SPECIFICATIONS:
5 flowmeters, range 0.125 – 2 l/m
5 outlets oxygen flow splitter, to be connected to a single oxygen supply/concentrator
Independent outlets (the cumulative maximum flow is limited by the supply flow)
Suitable for tabletop or wall mount
Input pressure 48 – 345 kPa

Contact Science Lab for your Educational School Science Lab Equipments. We are best technical educational instruments supplier, technical institute lab equipments, technical lab equipments manufacturers, top lab equipments manufacturers, tvet lab equipment manufactruers, vocational training lab equipments exporter, vocational training lab equipments manufacturers.

Reusable Humidifier Bottle Non Heated

Product Code : SLE/RAE/18

DESCRIPTION
A sealed bottle of water inserted into a breathing circuit to add moisture to the breathing gases for administration to a patient. This type of humidifier does not heat the gas.

TECHNICAL SPECIFICATIONS
Graduation shall show minimum and maximum water level.
Detachable metal or rigid durable polymer cap with gas connectors.
Non-heated, reusable humidifier for oxygen therapy and ventilation/anaesthesia inspiratory lines.
Bubble-through humidification system.
Graduated, transparent humidification bottle, shatter resistant.
DISS connectors for gas inlet and outlet
All available adaptors for gas connection to be described in bid response
Flow rate capacity up to 15 L/min.
Safety pop-off valve incorporated
Cap and connectors made of brass/steel/other biocompatible metal or polymer certified for medical use.
Bottle and tubes made of polymer certified for medical use, shatter resistant.
Autoclavable and/or disinfectable with hospital grade detergents.
Humidification chamber working volume at least 150 ml, not greater than 500 ml.

ENVIRONMENTAL CONDITIONS
Storage conditions temperature:
-20 °C to 60°C / RH: 15% - 90%
Operating conditions temperature: 5 to 45°C / RH: 15 to 90%

Contact Science Lab for your Educational School Science Lab Equipments. We are best science educational equipments, science educational instruments, science lab equipments manufacturer, science laboratory instruments exporter, scientific educational equipments, scientific educational lab equipment.

Ultrasonic Oxygen Analyzer Handheld

Product Code : SLE/RAE/19

DESCRIPTION
Hand held, battery powered device that measures the oxygen concentration in a flow of gas from a medical gas source or, with adapters, through a medical gas-flow device such as a ventilator or anaesthesia system. The intended application is checking gas supply equipment performance.

TECHNICAL SPECIFICATIONS
Operational Characteristics

Ultrasonic oxygen sensing technology, with permanent sensing chamber.
O2 measurement to include the range 21 - 96 %.
Hand-held oxygen analyzer for spot-check or continuous measurement of the oxygen concentration from a medical gas source.
Flow rate accuracy within ± 3 %
Flow rate resolution 0.1 LPM
Response time < 30 s.
Warm-up time < 15 s.
O2 accuracy: within ± 3 %.
Flow rate measurement: up to at least 10 LPM
Suitable for measuring gas supply with pressure up to 50 psi.
O2 resolution: 0.1 %.
Self-calibration in typical conditions of use.
Display visualizing O2 concentration, flow rate, system messages and battery status.

Electrical characteristics
Battery life > 250 hours continuous use.
Automatic power-off when not in use.
Operated by battery power supply.
2 x AA alkaline replaceable single use batteries.

Contact Science Lab for your Educational School Science Lab Equipments. We are best scientific educational lab equipments, scientific equipments manufacturers, scientific lab equipment manufacturers, scientific lab plasticware, scientific laboratory equipment manufacturer, scientific laboratory equipment supplier

Oxygen Flow Meter 0 – 15 LPM

Product Code : SLE/RAE/20

DESCRIPTION
Medical gas flow meter to regulate and measure the flow rate of medical gas supplied to a patient, maximum flow rate 15 LPM, for medical oxygen.

TECHNICAL SPECIFICATIONS
Graduation shall have over 270 degrees of visibility.
Needle valve and body constructed of brass or aluminium.
Thorpe tube design flow meter using DISS input connector for panel /regulator mounting.
Can be cleaned with damp cloth and a disinfection solution.
Transparent, graduated (metric system) column, shatter resistant polymer certified for medical use.
Calibrated at 50-55 psi / 345-380 kPa / 3.4-3.8 bar inlet gauge pressure.
Inlet pressure (nominal) > 50 psi (345 kPa / 3.45 bar), peak inlet pressure at least 100 psi (690 kPa / 6.89 bar).
Pressure compensated design to give specified accuracy for whole range of input pressures
Maximum flow rate when fully opened: 50 L/min 
Adjustment knobs to have rough surface to prevent slipping.
Built-in inlet filter 

OXYGEN Model:
0 - 15 L/min, accuracy 10%, tube gradation max 0.5 L/min at low flow, max 1 L/min high flow

Contact Science Lab for your Educational School Science Lab Equipments. We are best scientific laboratory equipments manufacturer, scientific laboratory equipments supplier, technical educational equipment exporter, technical educational equipment manufacturer, technical educational equipment supplier, technical educational equipments exporter.

Request A Catalog

Request A Catalog

Request Now for a Catalog and Get best deals for your Products

Request Now